World Of Controls understands the criticality of your requirement and works towards reducing the lead time as much as possible.
DS200UCIBG1A - UC2000 MOTHER BOARD is available in stock which ships the same day.
DS200UCIBG1A - UC2000 MOTHER BOARD comes in UNUSED as well as REBUILT condition.
To avail our best deals for DS200UCIBG1A - UC2000 MOTHER BOARD, contact us and we will get back to you within 24 hours.
Part Number: DS200UCIBG1A
Manufacturer: General Electric
Series: Mark V
Product Type: UC2000 Motherboard
Availability: In Stock
Country of Origin: USA
DS200UCIBG1A is a UC2000 Mother Board manufactured by General Electric as part of the Mark V Series used in gas turbine control systems. The R Core Mother Board provides the connectors for attaching the host CPU daughterboard, two GENI boards, and a flash drive (UCIB). The UCIB board uses a 196 microprocessor to translate the DLE gas fuel pressures coming from the TCSA board. These signals are written to the LBC586P board using the J1 and J3 bus connectors. The COREBUS and Stage Link signals that have been written to the PANA board are transferred to the LBC586P using the J1 and J3 bus connectors. The UCIB Motherboard has the GENI and LBC586P boards inserted. consists of a processor that transforms serial pressure transducer signals from the TCSA board for the LBC586P using a 196-bit bus. P1.
LBC586P Daughterboard on the UCIB with a Pentium processor. The PANA board for ARCNET connections is mounted on a daughterboard that is attached to the LBC586P. P1. TCSA – XDSA board on the gasoline skid and UCIB contain decoders for serial communication for Dry Low Emissions (DLE) applications. L2. The Fuel Skid Interface Board (TCSA), found in the R core, interacts with the XDSA board on the fuel skid for Dry Low Emissions (DLE) applications. The TCSA board decodes the signals from the high-resolution pressure transducers for the 196 processor on the UCIB board. The signals from XDSA are connected to the TBSA terminal board at position 8 of the R2> core.
J1 - Bus connector that communicates with the LBC-586 and PANA boards.
J2 - Connector for IDE flash drive.
J3 - Bus connector that communicates with the LBC-586 and PANA boards.
J4 - Routes IDE disk signals between the LBC-586 and UCIB boards.
Hardware: The clock is enabled by hardware jumper JP1. For details on the hardware jumper settings for this board, consult Appendix A and the operator interface's hardware jumper panel.
Software: The UCIB board has no software configuration.
The high-resolution pressure transducer signals are sent from the XDSA board to the TBSA terminal board in the R2 core. The P3 connector on the TCSA board receives the signals, which it then decodes for the 196 processor on the UCIB board to use. The signals are written to the LBC586P board using the J1 and J3 connections.
A GENI board could be mounted on the UCIB board. A GENI board regulates specific sorts of data flow between the host (Mark V LM) and the Genius bus. The connections for the Gen- ius bus are made on the 1TB terminal board on the "R" core. The P5 connector on the UCIB board is used to write signals to the LBC586P board, while the P3 serial connector is used to send signals from the GENI board to the UCIB board. The P15 connector on the UCIB board supplies power to the GENI board.
Many connectors on the LBC586P card are not used for the Mark V LM application. The following connections are made to the LBC-586 card:
J26 - Bus connector for processor interface to memory and IO on the UCIB and PANA.
J29 - Bus connector for processor interface to memory and IO on the UCIB and PANA.
J18 - IDE interface connector. Ribbon cable connected to J4 on the UCIB.
J7 - Power cable. Connected to P8 on the UCIB.
J3 - Serial and other miscellaneous signals. Connected to P13 on the UCIB.
WOC has the largest stock of Speedtronic Mark V replacement spare parts and we can repair your faulty parts with a warranty. WORLD OF CONTROLS can also supply UNUSED and REBUILT backed up with a warranty of up to 24 months. Our team of experts is available round the clock to support your needs. Our sales team at WOC is happy to assist you with any of your automation requirements. Please contact our staff by phone or email for pricing and availability on any parts and repairs.
What is GE Mark V DS200UCIBG1A?
One CPU and numerous programmable read-only memory modules are featured on the GE UC2000 Motherboard DS200UCIBG1A. One block of ten LEDs and a 50-pin connector are also included.
How to Check Price and Availability For DS200UCIBG1A?
Please Contact World of Controls FZE for sales at +1 609 385 1231 or Request a Quote.
How long does it take WOC to repair my boards?
Your boards will be repaired by WOC in 3 to 5 business days. WOC also offers up to 24 months customer satisfaction warranty on all repairs.
