[email protected]
+1 832 946 3166
Instagram

Ds3800haca1a

DS3800HACA1A - Address Customize Card

DS3800HACA1A - Address Customize Card DS3800HACA1A - Address Customize Card

World Of Controls understands the criticality of your requirement and works towards reducing the lead time as much as possible.

DS3800HACA1A - Address Customize Card is available in stock which ships the same day.

DS3800HACA1A - Address Customize Card comes in UNUSED as well as REBUILT condition.

To avail our best deals for DS3800HACA1A - Address Customize Card, contact us and we will get back to you within 24 hours.

Request For Quote
Contact Us

Featured Product

SPECIFICATIONS

Part Number: DS3800HACA1A
Manufacturer: General Electric
Series: Mark IV
Product Type: Address Customize Card
Availability: In Stock
Country of Manufacture: United States(USA)

DS3800HACA1A is an Address Customize Card manufactured and designed by General Electric. It is a Part of Mark IV series. The Circuit Board HACA is outfitted with a modular connector for attaching to a drive as well as retention levers to keep the board in place.

Testing

  • The Mark IV hardware is tested in four stages: components, cards, modules, and panels. All integrated circuits are subjected to three screens during the component test: temperature cycle, hermetic seal fine and gross leakage, and burn-in.
  • The ICs are then subjected to a 100% electrical parameter test. Printed wire boards (cards) are burned in at 155F for 160 hours with the power on, followed by an in circuit test and a functional test. If additional calibration is required, it is performed after the testing.
  • A General Radio GR2270 tester is currently being used for circuit and functional testing.
  • The tests are fully programmed, resulting in high consistency and accuracy. Individual tests on the modules range from simple back-plane inspections to automatic wiring scans on wired back-planes and cables to full functional testing of power supplies.
  • The total hardware configuration will be functionally tested on the C communicator and RST controller modules. A functional hardware test is performed on the fully assembled panel, during which all input signals are simulated and all output signals are validated.
  • The tests and measurements are made from the customer interfaces for completeness. The testing is fully programmed, providing a high level of assurance about the thoroughness and quality of the tests.

DS3800HACA1A Installation

  • The HACA is inserted into the board and slides into a board rack designed for easy and quick board installation and removal. The board's end is equipped with a module connector that allows connection to a matching connector in the drive's interior.
  • Retention levers are available to keep the board in place and ensure a secure connection. However, to ensure proper board operation and to extend the life of the drive's components and boards, it is critical to ensure that excessive heat does not build up in the drive interior. That is only possible if the installation is meticulously planned.
  • The drive is frequently installed in rooms with numerous other drives and other equipment nearby. When installing the drive, choose a location free of dust, dirt, harsh chemicals, and extreme heat and humidity. The drive is mounted on a wall with bolts that support its weight. Choose a location with enough space around all sides of the drive when it's installed.
  • Heat from devices on the other side of the wall can pass through the wall. Make sure the wall stays cool, and if that isn't possible, remove some equipment from the adjoining room near the wall.The HACA is inserted into the board and slides into a board rack designed for easy and quick board installation and removal. The board's end is equipped with a module connector that allows connection to a matching connector in the drive's interior. Retention levers are available to keep the board in place and ensure a secure connection. However, to ensure proper board operation and to extend the life of the drive's components and boards, it is critical to ensure that excessive heat does not build up in the drive interior.
  • That is only possible if the installation is meticulously planned. The drive is frequently installed in rooms with numerous other drives and other equipment nearby. When installing the drive, choose a location free of dust, dirt, harsh chemicals, and extreme heat and humidity. The drive is mounted on a wall with bolts that support its weight. Choose a location with enough space around all sides of the drive when it's installed.
  • Heat from devices on the other side of the wall can pass through the wall. Make sure the wall stays cool, and if that isn't possible, remove some equipment from the adjoining room near the wall.

WOC has the largest stock of GE Replacement Parts. WOC is happy to assist you with any of your automation requirements. For pricing and availability on any parts and repairs, kindly get in touch with our team by phone or email.

 

FREQUENTLY ASKED QUESTIONS

 

What is DS3800HACA1A?
DS3800HACA1A is an Address Customize Card manufactured and designed by General Electric

How are boards packaged for shipment from WOC?
Parts are placed in antistatic packets and securely packed in ESD boxes cushioned with ESD Foam designed to safeguard electrical components.